Product Details
Usual 380V 30KW Solar Pump Inverter Three Phase

General Parameters of 30kw solar pump inverter:

DC Input Range (VDC) 250 to 800
Recommended MPPT voltage 90-800Vdc
Max. MPTT efficiency >97%
Models SPIG300-030GB-T4
Max. applicable pump output power 30KW
Rated output voltage 380V-440V ac 3 phase
Output frequency range 0-50/60Hz
Rated output current 60A
Dimension(W/H/D,mm) 432*285*225
Module IGBT
weight 10kg
Max. efficiency >97%
Protective class I
Protection degree IP20
Environment temperature -25ºC-+70ºC 
Cooling method Natural cooling&fans
Display  LCD
Communication interface RS485
Altitude  3000m
Noise emission <50dB
compliance EMC&LVD

Features of automatc solar pump converter

1.Self-diagnostic and protection
2.Maximize your pump delivery without wasting a watt
3.Automatic start and stop with solar irradiation
5.Dry run protection 
6.Compatible with all pumps with easy operation
7.No need parameters setting after pumps correct selection
8.DC current, voltage, power input can be monitored, easy to know power input
9.Laptop software control is available , remote control management with GPRS/GPS is optional
10.Good quality with Infineon IGBT module and other top brand components using
11.Long term guarantee with 18 months.

Advantages of submersible solar pump controller: 

1. High quality with 18 months warranty
2. Controlling with open-loop, closed-loop control
3. Install PID, main spindle control for water pump
4. Module bus communication protocol,RS485 communication
5. Simple PLC and multistage speed
6. In-built MPPT with high efficiency 
7. Speed tracking function 
8. Carrier frequency automatic adjustment
9. Various protection mechanisms (over current/over voltage/overload, overheating, etc), to protect water pumps

Application of 50/60HZ solar pump controller:
1.Remote Villages, Homes, Cabins and Hunting Lodges (home use)
2.Irrigation for remote orchards, gardens, and greenhouses (irrigation water)
3.Wildlife watering at wild game parks and farms (irrigation water)
4.Fish pond water level maintenance and aeration (home use)
5.Swimming pool circulation& filtration pumps (home use)
6.Surface water pumping for landscaping streams and waterfalls (home use)
7.Cattle, Livestock watering systems (animal husbandry )
8.Water supply for sea island
9.Water treatment projects, for example, sea water desalination

Installation diagram:


Electrical safety notice of automatic water pump converter!
Ignoring the following instructions can cause physical injury, or damage to the equipment.
Only qualified electricians are allowed to install and maintain the inverter!
• Never work on the photovoltaic generator or inverter and its input/output cables when the inverter is connected to the power system or to the photovoltaic generator.
• Before working inside the inverter cabinet, switch off or isolate the auxiliary voltage supply to the inverter.
• Isolate the inverter from the photovoltaic generator using the safety switch of the generator or by using the isolation switch.
• Do not touch the input of the isolation switch that has high DC voltage.
• After disconnecting the inverter from the power system or the DC input supply, wait for at least 5 minutes to discharge the intermediate circuit capacitors.
• Measure with a multimeter to ensure that no voltage is present.
• Impedance should be at least 1 MΩ.
• Voltage should be close to 0 V between inverter phases L1, L2, L3 and frame, and between module terminals Brk+ and Brk-.
• Do not make any insulation or voltage withstand tests on the inverter or on the inverter modules.
• The DC connection terminals Brk+ and Brk- carry a dangerous DC voltage of up to 800 V.
• Depending on the external and internal wiring, dangerous voltages of 115 V to 230 V may be present at the different terminals in the auxiliary circuit.
• At the inverter input, the photovoltaic cells generate DC voltage even at low intensity of sunlight.